Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the full feature guide as PDF

Troubleshooting: schedules and time ​

The schedule time came but the image didn't change ​

Check in order:

CheckWhere to lookFix
Is the schedule disabled?The card shows "Disabled" and the table shows "Paused"Turn on the switch at the bottom of the card
Is the image set empty?The card has no thumbnail, only an image iconAdd images to the image set
Was the image set deleted?The card shows "No image set selected"Edit the schedule and choose an image set again
Does the image set have only one image?The same image is refreshed every time, so it looks unchangedAdd more images
Just created and the first time hasn't come yetCheck the card countdown or "Next Run"Wait for the first time
This round was skippedThe card briefly flashed a red ✕It plays at the next successful trigger; if it keeps getting skipped, move the times apart
Wrong device timeTime settingsCorrect the time
Device powered offStatus LED off, buttons don't respondSchedules don't run while the device is off

The schedule runs at the wrong time ​

  1. Wrong time zone. Schedules run on the device time zone. When the "Timezone mismatch" notice appears on the schedule page, press "Sync to …". You can also change it in Time settings.
  2. Device time is wrong. Go to Time settings and press "Sync Local Time".
  3. "Next Run" looks wrong. "Next Run" in the table is shown in the device time zone. If the time is off from what you expect by a few hours, the device time zone is usually set wrong; check the time zone first.

A weekday schedule runs on Saturday and not on Monday ​

In version 1.10.0 and earlier, when days of the week are written as numbers in a cron expression, the actual trigger day is shifted one day later (for example, 1-5 becomes Tuesday to Saturday). This is fixed in 1.11.0, and existing schedules with numeric days are corrected automatically after the update.

Fix: Update the device to 1.11.0 or later. If it's still wrong after the update, edit the schedule and pick the days again in the "Specific time" editor. See Known issue with the day-of-week field.

A red ✕ or "Conflict" appears on the card ​

DisplayMeaningFix
Red ✕ (about 2 seconds)The panel was busy when it was time to change images this round, so it was skippedIt plays at the next successful trigger; if it keeps getting skipped, move the times apart
Red vignette + "Conflict"Due to trigger at the same moment as another schedule; this one is listed later and will be skipped this roundMove the two schedules' times apart, for example one at :00 and one at :05

See Schedules — simultaneous triggers and skips.

"Creation failed" or "Update failed" when saving a schedule ​

  • If you typed a cron expression manually in advanced mode, the format may be wrong. Check the description below the field: if it shows exactly what you typed, the format is wrong.
  • The image set you chose may have just been deleted by someone else. Choose it again.
  • Press "Back to selection mode" to use the graphical settings instead; that usually avoids errors.

The light doesn't turn on and off on schedule ​

  1. Check that the schedule is enabled and that "Next Run" is correct.
  2. A light schedule runs only once, at the moment it triggers; in between, the light stays in its last state. Check that you have both an on schedule and an off schedule.
  3. If on and off are set to the same minute, the result is unpredictable. Move them apart.
  4. Did you edit a disabled light schedule? It may have become enabled again automatically. Check its status switch.
  5. For day-of-week conditions, see "A weekday schedule runs on Saturday" above.

See Light schedules and the light.

Tapping the light bulb icon does nothing and jumps to the schedule page ​

While any light schedule is enabled, you can't turn the light on or off manually (the bulb is gray). To control it manually, disable all light schedules first.

The device time is wrong ​

  1. Go to Time settings and press "Sync Local Time". If the button is gray, turn off "Set time automatically (NTP)" first.
  2. "Real-time clock (RTC) fault" appears at the top of the page: the hardware clock has failed, the time will gradually drift and the device can't wake up from sleep automatically. Reboot; if it still appears, contact technical support. See Hardware warnings.
  3. NTP showing "Not Synced" is normal (the device has no external network) and doesn't affect use.

Related: Schedules, Schedule frequency in detail, Time, time zone and time sync

Green Ideas Technology