Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the full feature guide as PDF

Battery ​

Navigation: Settings → Power → Battery Info, or click the battery icon in the upper right of the management interface

Applicable models

The battery icon and the "Battery Info" page appear only on models with the optional battery. Models without a battery don't show them. See Models and specifications.

Battery icon in the upper right ​

The upper right of the management interface always shows the battery level, updated every 30 seconds; it updates immediately when the charging state changes.

DisplayMeaning
Battery icon + "NN%"Current battery level. Hovering shows "Battery: NN%"
GreenBattery level above 50%
YellowBattery level 21%–50%
RedBattery level 20% or below
Lightning bolt iconCharging
Gray warning icon + "--"Battery data can't be read (not 0%). Hovering shows "Battery service unavailable — tap for details"

Click the icon to open the Battery Info page.

"--" is not the same as "0%"

"--" means battery data can't be read (the battery management system isn't responding, no battery is connected, and so on); "0%" means the battery level really was read as 0. If you see "--", open the Battery Info page and check "Data health".

Battery Info page ​

The page has three tabs: Overview, Monitor, and Details. In the upper right you can choose how often the data updates (10 seconds, 30 seconds, 1 minute, 5 minutes; default 1 minute), or press the refresh icon to update right away (on success it shows "Battery info updated").

Overview ​

ItemDescription
BatteryRemaining battery percentage in large type, with the charging state below (see the table below)
Time left / Time to fullRemaining run time (when discharging) or time to full charge (when charging), estimated from the present current
RemainingIn Ah
Charging power / Discharging powerIn W
TemperatureTemperature measured by the battery management system (°C)
VoltageIn V
HealthBased on SOH: 90% or above "Good", 75% or above "Fair", below 75% "Check", unreadable "Unknown"
Cycle CountNumber of charge/discharge cycles
CurrentIn A

Estimated times change

"Estimated from the present current; actual time varies with usage." When the device displays images or the light is on, the current rises and the estimated time drops instantly. Treat it as a reference, not a guaranteed run time.

If data can't be read, all values show "-", not 0.

Charging stateMeaning
ChargingExternal power is connected and the battery is charging
Fully chargedExternal power is connected and the battery is fully charged. The battery level shows 100%
Plugged in, not chargingExternal power is connected, but the battery isn't charging right now
On batteryNo external power; the device runs on the battery
  • After the battery is fully charged, the level reported by the battery management system often stays at 99%. When external power is connected and the battery is fully charged, the upper right and the Overview show 100%; "SOC" on the "Details" tab still shows the raw value reported by the battery management system.
  • Older battery boards can't report whether external power is connected; in that case only "Charging" or "On battery" is shown.

Monitor ​

Live trend charts, including: health (SOH), cycle count, number of samples, temperature and total voltage trends, a current gauge, charging/discharging power, and remaining and estimated full capacity.

The trends cover only the samples taken while this page is open (up to 180); reloading starts over. This is not a long-term history of the battery.

Details ​

Full values for troubleshooting: charging state, battery level (SOC), health (SOH), remaining capacity, total voltage, current, temperature, cycle count, voltages of cells 01–06, spread (difference between the highest and lowest cells), protections and alarms, firmware version, battery management system time, data health, and the BMS status raw value.

Footer note: "These values come straight from the battery board (BMS) and are meant for troubleshooting. The temperature is measured on the board, not ambient."

Data health ​

DisplayMeaningWhat to do
NormalData is read normally; values are reliable—
Data out of dateThe battery management system hasn't sent new data for too long; values may be oldReload later; if it keeps happening, restart the device
No battery detectedThe battery management system responds, but all values are 0; usually the battery isn't connectedCheck that the battery is in place and the connector is properly attached
Battery management system not respondingThe battery management system doesn't respondCheck the battery management system and the cable, and restart the device
Battery management system not foundCan't connect to the battery management systemHardware connection problem; contact technical support
Legacy service (not reported)The battery service on the device is an older version and can't tell whether the data is reliableAvailable after you update the software

If the battery service can't be reached at all, the page shows "Battery Service Unavailable: Cannot connect to battery service. Please check hardware connection or service status." and you can press Retry.

Protections and alarms ​

"Protections and alarms" lists the items the battery management system has currently triggered. When everything is normal, it shows a green check with "All normal".

  • Red tag = protection: the battery management system has stepped in and cut off charging or discharging. This is an abnormal situation.
  • Yellow tag = alarm: the BMS is reporting a warning, but no protection has been triggered and the battery is still working normally. For example, "Overvoltage Alarm" when the battery is nearly full is normal.
  • Blue tag = information: a notice about a normal state, not an abnormality. Currently the only one is "Fully charged" (the battery is fully charged).
TypeItems
Protection (red)Undervoltage, Overvoltage, Charge Overcurrent, Secondary Charge Overcurrent, Discharge Overcurrent, Secondary Discharge Overcurrent, Discharge Overload, Charge Short Circuit, Discharge Short Circuit, Charge Over-temperature, Discharge Over-temperature, MOS Over-temperature, Charge Timeout
Alarm (yellow)Undervoltage Alarm, Overvoltage Alarm, Charge Low Temperature, Discharge Low Temperature, Discharge High Temp Alarm, Charge High Temp Alarm, Discharge Overcurrent Alarm, Charge Overcurrent Alarm
Information (blue)Fully charged

If a red protection tag appears

Write down the time, the tag name, each cell voltage, and the "BMS Status Raw Value", stop using the device, and contact technical support. Don't disassemble the battery or change any protection settings yourself.

If a yellow alarm tag appears

The BMS is reporting a warning and no protection has been triggered yet, but you can't conclude from the color alone that the battery is definitely fine. Write down the warning name, the time, and the related readings; if it persists or keeps coming back, contact technical support.

Battery and power saving ​

  • The panel is powered only while an image is being displayed, and power is cut when it's done; a cholesteric LCD holds its image without power, so showing a still image uses almost no power.
  • Power is mainly used by: how often images are displayed, the system running, the Wi-Fi hotspot, and the light (on models with a light).
  • The most effective ways to save power: turn on sleep and change images less often in your schedules.
  • The management interface has no low-battery auto-shutdown setting; when the battery is too low, the battery management system's hardware protection cuts the power. At 20% or below, the icon in the upper right turns red; charge as soon as possible.

FAQ ​

Q: The battery in the upper right shows "--"? Battery data can't be read. Open the Battery Info page, check "Data health", and follow the table above.

Q: The battery shows 0%, but the device is still running? If the device has an older battery service, it shows 0% when it can't read data. After you update to the latest software, it can tell "really empty" apart from "can't be read".

Q: Do I need to do anything about a yellow "Overvoltage Alarm"? It's normal when the battery is nearly full; no action needed. Only the red "Overvoltage" protection means the battery management system has stepped in.

Q: The estimated run time keeps jumping around? The estimate is based on the current at that moment: the current is high while displaying images and low when idle, so the number changes accordingly. This is normal.

Related sections: Sleep and wake up, Power control and storage, Troubleshooting: power, sleep, and battery

Green Ideas Technology