Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the full feature guide as PDF

Troubleshooting: power, sleep and battery ​

The device never goes to sleep ​

CheckDescription
Is sleep turned on?The factory default is off; turn it on in Sleep settings
Does anyone have the management interface open?While anyone has any page open, the device must be idle for at least 15 minutes, plus a 60-second countdown. Close all tabs when testing
Is the schedule very frequent?With an image change every minute, there's almost no chance to sleep
Is the panel refreshing all the time?The device doesn't sleep while refreshing
Is there a "Real-time clock (RTC) fault" warning?When there are enabled schedules but the hardware clock can't be found, the device doesn't sleep (so that schedules can still wake it). Reboot; if it still appears, contact technical support

Search the system logs for the keyword 取消休眠 (sleep canceled) to see why the device didn't go to sleep.

The device won't wake up from sleep ​

  1. Press a physical button once and wait a few seconds.
  2. If the status LED is still off and the buttons don't respond, the device may be powered off or out of power (on battery models, the battery management system cuts the power when the charge is too low). Connect power and turn it on.
  3. If your phone can't connect after it wakes up, the hotspot needs a few seconds to restart. Wait a moment, then connect.

Schedules didn't run during sleep ​

  1. Is the schedule enabled? Disabled schedules don't wake the device.
  2. Is there a "Real-time clock (RTC) fault" warning? When there are enabled schedules, a device with a hardware clock fault doesn't go to sleep; a device that was already asleep before the warning appeared may not wake up automatically, so wake it with a button. Reboot; if it still appears, contact technical support.
  3. Are the device time and time zone correct? Check in Time settings.
  4. Light schedule events missed during sleep aren't run afterward, but after waking up the light is corrected to the right state for the current time.

The battery shows "--" or 0% ​

DisplayMeaningFix
Gray "--"Battery data can't be readCheck "Data health" in Battery info
Data health "No battery detected"The battery may not be connectedCheck the battery connector
Data health "Battery management system not responding" or "Battery management system not found"The battery management system or its cable has a problemReboot; if it's still wrong, contact technical support
Data health "Data out of date"The battery management system hasn't sent data for too longRefresh later
0% (shown in red)Really out of power, or an older battery service can't read the dataCharge it; after a software update the two cases can be told apart
"Battery Service Unavailable"Can't connect to the battery servicePress "Retry", or reboot

A red protection tag appears on the battery ​

The battery management system has cut off charging or discharging. Note the tag name, each cell voltage and the raw BMS working status, stop using the device and contact technical support. A yellow "alarm" means the BMS reported a warning without triggering protection yet, but you can't judge that the battery is definitely fine from the color alone. See Battery — protections and alarms.

The status LED keeps blinking ​

Status LEDPossible causeFix
Slow blink (slow white blink on full-color LEDs)Starting upWait for startup to finish. If "Show QR Code startup screen on boot" is off, the LED may not switch to standby until the first refresh; just display an image
Continuous fast blink (fast red blink on full-color LEDs)A button is being held down, and the factory reset countdown has startedRelease the button immediately. Check whether something is pressing on the button
Breathing (blinking blue on full-color LEDs) for a long timeThe panel is refreshingRefresh time depends on the model and refresh mode, for example about 6 seconds on 13.3-inch, about 16 seconds on 27.6-inch, about 20 seconds on 32-inch; if it takes more than 2 minutes, reboot

I shut it down but wanted to restart it ​

You can't power the device on remotely after shutdown; someone has to handle the power on site. To save power normally, use sleep.

The panel didn't turn white after shutdown or reboot ​

The system clears the screen before shutdown and reboot, and retries 2 times if it fails; if it still fails, it shuts down anyway so shutdown can complete. After startup, first press "Clear screen" to check that the panel is normal, and check the system logs.

Related: Sleep and wake-up, Power control and storage, Battery

Green Ideas Technology