Network settings
Navigation: Settings → System → Network
This page decides how the device connects: broadcasting only its own hotspot, joining the on-site Wi-Fi, or both at once. The hotspot name and password, the list of on-site Wi-Fi networks and the phones currently on the hotspot are all managed here too.
Network overview
When you open the "Network" page, you see a list of settings:
| Item | Shows | Action |
|---|---|---|
| Network mode | The current mode: one of "Hotspot", "Station" and "Concurrent" | Click the mode you want to switch to |
| Hotspot | The hotspot name and "N device(s) connected"; when the hotspot is off, "Hotspot is currently off" | Press "Configure" to open "Hotspot" |
| Wi-Fi | When connected, the network name and address; when not connected, "Not connected · N saved network(s)"; when the list is empty, "No network configured yet" | Press "Configure" to open "Wi-Fi" |
| Ethernet | The adapter name and address, or "Cable unplugged" | Press "Configure" to open "Ethernet". This row appears only when an adapter is detected |
| Allow DFS channels | A switch; see Allow DFS channels | "Updated" appears after you toggle it |
When a feature is restricted (for example, the hotspot channel is forced to change), the reason is written in a warning color under the affected row; see Network status notices.
While viewing another device in the cluster
"Network" can only be used in this device's own management interface. When you view another device from the cluster, this item on the Settings page shows "Open this page on that device".
The three network modes
| Mode | What the device does | How your phone reaches the management interface | Best for |
|---|---|---|---|
| Hotspot (factory default) | Broadcasts only its own Wi-Fi hotspot and doesn't join any outside network | Join the device's hotspot and open http://192.168.100.1 (the hotspot's default address) | No network on site, a single device or a few, temporary demos |
| Station | Joins the on-site Wi-Fi, with the hotspot off | Join the same on-site Wi-Fi with your phone and open the address the on-site network assigned to the device | Devices installed permanently at a site with a network, managed on the same network as other equipment |
| Concurrent | Joins the on-site Wi-Fi and keeps the hotspot | Either way: join the hotspot, or join the same on-site Wi-Fi | Normally using the on-site network, but keeping the hotspot as a backup way in |
"Station" needs at least one network saved under On-site Wi-Fi first; if you click it while the list is empty, "No Wi-Fi network yet" appears; press "Add one" to add a network first. "Concurrent" can be selected before any network is saved: the hotspot stays on and your phone stays connected, and the device joins the site Wi-Fi once you add it.
In Concurrent mode the hotspot is affected by the on-site network
In Concurrent mode the device's Wi-Fi adapter can use only one channel at a time, so the hotspot channel follows the on-site Wi-Fi and can't be chosen. If the on-site Wi-Fi is on 2.4 GHz, the hotspot becomes 2.4 GHz too. See Network status notices.
Switching the network mode
- Under "Network mode", click the mode you want to switch to.
- A "Switch to “mode name”" confirmation window appears, describing the consequences of this switch (see the table below).
- Press "Switch".
- The screen shows "Applying network settings…": "Do not close this page or unplug the device. A brief disconnect on your phone is normal; the result appears once it reconnects."
- On success, "Switched to “mode name”" appears; if the device got a new address, "New address: …" is shown as well.
How each switch affects your phone
| Switch | Confirmation window text | Phones connected through the hotspot |
|---|---|---|
| Hotspot → Station | "The hotspot will shut down, and phones or tablets connected through it will be disconnected." | Not disconnected during the trial connection; after a successful switch the hotspot stays on for 5 more minutes, see the next section |
| Hotspot → Concurrent | "The device will join the Wi-Fi network and keep its hotspot; the hotspot channel will follow the Wi-Fi network, which may briefly interrupt connections." | The hotspot stays, but may drop briefly and reconnect automatically |
| Station → Hotspot | "The device will leave the Wi-Fi network and keep only its own hotspot. Anyone using this page through the Wi-Fi network will be disconnected." | (The hotspot was off.) Anyone working through the on-site Wi-Fi is disconnected; join the device's hotspot instead |
| Concurrent → Hotspot | Same as above | The hotspot stays; anyone working through the on-site Wi-Fi is disconnected |
| Concurrent → Station | "The hotspot will shut down, and phones or tablets connected through it will be disconnected." | Disconnected immediately, with no grace period |
| Station → Concurrent | "The device will join the Wi-Fi network and keep its hotspot; the hotspot channel will follow the Wi-Fi network, which may briefly interrupt connections." | (The hotspot was off.) The hotspot turns back on |
When switching to "Station" or "Concurrent", the confirmation window also says: "The device first tries the Wi-Fi network (up to about 30 seconds). If it cannot connect it rolls back, leaving no half-applied settings." and "Once done, reconnect your phone to the same Wi-Fi and open the new address to see the result."
From Hotspot to Station: the hotspot stays on for 5 minutes
After a successful switch from "Hotspot" to "Station", the hotspot doesn't disappear right away. The result page shows "The hotspot stays on for 5:00, then shuts down automatically." and starts counting down. This time lets you:
- Note the new management address on the result page.
- Switch your phone to the same on-site Wi-Fi.
- Open the management interface at the new address and check that it works.
Once everything is fine, you can press "Done — close the hotspot now" to close it early; on success, "Hotspot closed" appears. You don't have to press it: the hotspot closes automatically when the countdown ends.
Note the new address before leaving the hotspot
Once the hotspot is closed, the device can only be found through the on-site Wi-Fi. If you forget the new address, look at the startup screen on the device panel (in Station mode the startup screen shows the on-site network address, see Startup screen and network mode), or ask the network administrator to look it up on the router.
If the switch fails
If the trial connection fails, the device automatically returns to the previous mode. The screen shows "Could not switch to “mode name”", "Rolled back to the previous settings." and the reason, with a "Check Wi-Fi settings" button:
| Reason | What to do |
|---|---|
| Reason: wrong password. | Enter the password again in Network properties |
| Reason: network not found — it may be out of range. | Check the network name and that the router is on, or move the device closer to the router |
| Reason: connected, but no address was assigned. | The on-site network didn't assign an address to the device; ask the network administrator, or use a static IP |
| Reason: this network uses a DFS channel, which is not allowed alongside the hotspot. | See Allow DFS channels |
| Reason: timed out. / Reason unknown. | Try again later |
Other notices:
| Notice | Meaning |
|---|---|
| The network is still applying an earlier change. Please try again shortly. | The previous network change hasn't finished yet |
| The network service is not responding. Please try again later. | The device's network functions are still starting or temporarily busy |
| No result yet | No result arrived after a long wait: "Make sure your phone is back on the device’s network and refresh, or check the Network page for the current state." |
Hotspot settings
Navigation: Settings → System → Network → Hotspot → Hotspot
Hotspot status
The hotspot name is shown in large text at the top of the page, with "N device(s) connected" below it. In "Station" mode the hotspot is off, and this area shows "Currently in Station mode — the hotspot is off" instead.
The QR code icon next to the name ("Show QR code") opens the "Scan to join Wi-Fi" window: "Scan with a phone camera to join without typing the password." This is a quick way to let other people on site connect.
Connection details
| Field | Description |
|---|---|
| WiFi Name | The hotspot name; can be copied |
| Password | Masked with "•" by default; press the eye icon to show it, and copy it while shown |
| Security type | The hotspot's encryption; see Security type |
| Channel | The channel the hotspot uses. When set to automatic it shows "Auto (currently N)"; in Concurrent mode it shows "N (follows the Wi-Fi network)" |
| Band | For example "5 GHz" |
| IP Address | The device address; can be copied |
| MAC Address | The hardware address of the device's Wi-Fi adapter |
Mask the password before sharing screenshots
The password and the QR code from "Show QR code" both let anyone connect directly to the device, and anyone on the hotspot can use the management interface. Before sharing a screenshot with others, make sure the password is masked, and don't share the QR code screen.
Changing the hotspot name and password
- Press the edit icon ("Edit hotspot") at the top right of "Connection details".
- Change the fields (see the table below). Advanced fields are under "Advanced"; click to expand it.
- Press "Save and restart hotspot".
- "Save hotspot settings?" appears: "The hotspot restarts after saving, so connected devices will disconnect and must rejoin with the new name or password. If you are using the hotspot right now, reconnect to see the result. If the startup screen is showing, its QR code updates automatically." Press "Save and restart".
- The screen shows "Restarting the hotspot…": "Your phone will disconnect briefly. Join “new name” and reopen this page; the result appears automatically."
- Rejoin the hotspot with the new name and password and reopen the management interface; you'll see "Hotspot updated".
If you press save without changing anything, the window simply closes and the hotspot isn't restarted.
| Setting | Range | Description |
|---|---|---|
| Name (SSID) | 1–32 bytes (a CJK character takes 3) | The name shown in your phone's Wi-Fi list. Hidden hotspots aren't supported |
| Password | 8–63 characters | The hotspot has no "unencrypted" option; a password is always required |
| Security type (advanced) | One of three | See the next section |
| IP address (advanced) | An IPv4 address | "This is also the address of the management page". Default 192.168.100.1 |
| Subnet mask (advanced) | For example 255.255.255.0 | The range of addresses the hotspot gives to phones |
| Channel (advanced) | "Auto" or 1, 6, 11, 36, 40, 44, 48, 149, 153, 157, 161, 165 | 1, 6 and 11 are 2.4 GHz; the rest are 5 GHz. Can't be changed in Concurrent mode: "In Concurrent mode the Wi-Fi network decides the channel" |
If a value has the wrong format, an error appears, for example "Name must be 1–32 bytes (a CJK character takes 3)", "Password must be 8–63 characters" or "Invalid address, e.g. 192.168.100.1".
If saving fails, "Hotspot update failed" and "Restored the previous settings." appear, and the hotspot keeps its previous name and password.
Changing the IP address changes the management interface address too
The hotspot's IP address is the management interface address. After changing it, open the new address (for example, after changing it to 192.168.50.1, open http://192.168.50.1); old bookmarks stop working.
When choosing channel 1, 6 or 11
These three are 2.4 GHz channels. Once the hotspot moves to 2.4 GHz, connections are slower than on 5 GHz, and devices that support only 5 GHz can't find the hotspot. Unless you have a specific need, keep "Auto".
Security type
| Option | Description in the interface |
|---|---|
| WPA2/WPA3 mixed (default) | "Both old and new phones can connect. Recommended." |
| WPA2-Personal AES | "WPA2 only. Phones without WPA3 support can still connect." |
| WPA3-Personal AES | "WPA3 only. Older phones without WPA3 support will not be able to connect. If that happens, use the rescue hotspot on the device to change it back." |
The hotspot offers no open (unencrypted) option: anyone on the hotspot can operate this device, so the hotspot password is the only protection.
When you change the security type, the QR codes on the startup screen and in "Show QR code" switch to the matching format, so scanning them still joins directly.
Hotspot factory values
| Item | Factory value |
|---|---|
| Name | The device name (set during installation) |
| Password | Depends on the device; see Connecting to the device — Hotspot password |
| Security type | WPA2/WPA3 mixed |
| IP address | 192.168.100.1 |
| Band | 5 GHz |
| Internet | Not provided (your phone may show "No internet"; this is normal) |
Connected devices
The lower part of the "Hotspot" page lists every phone or computer currently on the hotspot, updated automatically every 30 seconds:
| Shows | Description |
|---|---|
| MAC address | The network adapter address of that phone or computer |
| IP address · rate | The address the hotspot gave it and the connection rate |
| Signal bars + dBm | Signal strength; the closer the number is to 0, the stronger (for example, -45 dBm is stronger than -75 dBm) |
When no device is connected, "No devices connected" appears. Phone names aren't shown here.
This list shows only phones on the hotspot. Phones or computers that open the management interface through the on-site Wi-Fi don't appear here.
Device details and disconnecting
Click a device to open "Device details" on the right, showing the MAC address, Received, Sent, IP Address, Signal (dBm) and Rate.
Press the red Disconnect → confirm "Disconnect this device?" (It can join again — this is not a block.) → on success, "Device disconnected" appears.
- This only kicks the device off; if the phone remembers the hotspot, it usually reconnects automatically. To keep it from connecting again, change the hotspot password.
- If you kick off the phone you're using, you're disconnected immediately.
- If the button is grayed out with the notice "The hotspot control interface is not enabled on this device yet; it becomes available after a restart.": older devices need to be restarted once after a software update before this feature can be used.
On-site Wi-Fi
Navigation: Settings → System → Network → Wi-Fi → Wi-Fi
This is where you manage the on-site Wi-Fi networks the device should join (for example, a shop's or company's wireless network). The page has three rows:
| Row | Description |
|---|---|
| Current connection | When connected, shows the network name and "Connected, secured" or "Connected, open network"; press "Properties" for details. When not connected, shows "Not connected to any Wi-Fi network" |
| Show available networks | "Scan for nearby Wi-Fi and connect"; scanning starts when you expand it |
| Manage known networks | "Add, remove and edit networks (N saved)"; press "Manage" |
In "Hotspot" mode, the first row shows "Hotspot-only mode": "Not connecting — switch to Station or Concurrent mode to use Wi-Fi", with a "Switch mode" button next to it; "Show available networks" can't be used either ("Scanning is unavailable in hotspot-only mode"). You can still go to "Manage known networks" and use "Add network" to save networks in advance.
Connecting from nearby networks
- Expand "Show available networks"; the screen shows "Scanning — this takes about 10 seconds…".
- The list shows nearby networks and their signal strength. Networks with a lock icon need a password; saved ones are marked "Saved".
- Click a network, enter the password (8–63 characters) and press "Connect". Open networks need no password.
- The device first tries to connect and saves the network only if it succeeds; on success, "Saved" appears.
If you don't see the network you want, press "Rescan", or press "Add manually" to type it in yourself (hidden networks must be added this way). Clicking a saved network shows "This network is already saved"; press "Properties" to open its settings.
Adding a network
Press "Add network" on the "Manage known networks" page, or "Add manually" under "Show available networks":
| Field | Description |
|---|---|
| Name (SSID) | The network name; upper and lower case must match exactly |
| Security type | "Open", "WPA2-Personal AES", "WPA3-Personal AES", "WPA2/WPA3 mixed"; default "WPA2/WPA3 mixed" ("Accepts both WPA2 and WPA3; fits most routers.") |
| Password | 8–63 characters; not needed for "Open" |
| Hidden network | Turn on if the router doesn't broadcast its name |
Press "Test and save". The device first tries to connect to the network:
- If it connects: the network is saved and "Saved" appears.
- If it can't connect: the network isn't saved, and the window shows "Not saved." with the reason (for example "Reason: wrong password."); fix it and press the button again.
You can also press "Pick from scan results" to pick a network from the nearby list instead and then enter its password.
IP and DNS aren't set when adding; change them afterwards in that network's Network properties.
Passwords can only be written, never shown
Once an on-site Wi-Fi password is stored on the device, no screen ever shows it again; the network properties page only says "Set". If you forget the password, ask the network administrator; it can't be retrieved from the device.
Known networks and priority
The "Manage known networks" page lists all saved networks. The one currently in use is marked "Connected", and those preset on the production line are marked "Factory".
"Networks are tried in order; higher ones win." Use "Move up" and "Move down" on each row to change the order. When several known networks are in range, the device joins the one highest in the list.
Click a network name or the arrow on the right to open that network's Network properties.
Network properties
Each saved network has its own properties page (titled "network name properties"). In the upper part, each row has its own "Edit" button:
| Row | Shows | When editing |
|---|---|---|
| Password | "Set" | A "Change password" window: enter the new password (8–63 characters) and press "Test and save" |
| Security type | The current encryption | Choose the new encryption. The password field says "Leave blank to keep the current password"; in cases such as changing from "Open" to an encrypted type, "This change requires re-entering the password" appears |
| IP assignment | "Automatic (DHCP)", or "Manual address Mask Gateway" | See the next section |
| DNS server assignment | "Automatic (DHCP)", or the manually set DNS servers | See the next section |
When you change the password, security type or IP, the device reconnects to test it ("Changing the IP reconnects the device. If it cannot connect, the previous settings are restored automatically."). If it fails, the window shows "Not saved." with the reason, and the previous settings are not affected.
The lower part is read-only information: Name (SSID), Source ("Factory" or "Added by user"), Hidden network; for the network currently in use it also shows Band, Signal, Address, Gateway and DNS servers.
IP assignment and DNS server assignment
IP assignment (press "Test and save"):
| Option | Description |
|---|---|
| Automatic (DHCP) | The on-site router assigns the address (default) |
| Manual | Fill in "Address" (for example 192.168.1.50), "Subnet mask" (for example 255.255.255.0) and "Gateway". The gateway must be in the same subnet |
DNS server assignment (press "Save"):
| Option | Description |
|---|---|
| Automatic (DHCP) | Uses the DNS servers the router hands out (default). With a static IP: "A static IP has no router to hand out DNS, so Automatic means no DNS" |
| Manual | "Preferred DNS", "Alternate DNS", "Third DNS": "Tried in order, up to 3. When set, only these are used and the router’s are ignored" |
Changing only the DNS takes effect immediately, without reconnecting.
Check with the network administrator before using a static IP
If the address you enter is the same as another device's on site, or isn't in the router's subnet, the device may not be able to connect. Ask the on-site network administrator for an address reserved for this device.
Deleting a network
On the network properties page, press the red "Forget this network" → confirm "Delete this network?" ("The device will no longer join it automatically.") → "Deleted" appears.
Networks marked "Factory" can't be deleted; the button is grayed out with the notice "Factory networks cannot be deleted".
Before deleting all networks
Both "Station" and "Concurrent" modes rely on this list to connect; if you delete the network in use, the device can no longer reach the on-site network. Switching to CMS mode also needs at least one network in the list; see CMS / standalone mode switching.
Ethernet
Applicable models
Standard models have no wired network. The "Ethernet" row appears on the "Network" page only when the device detects an Ethernet adapter. If you open this page directly and there is no adapter, "No Ethernet adapter detected" appears.
Each adapter shows its name and "Connected" or "Cable unplugged". You can change "IP assignment" and "DNS server assignment" (same options as for on-site Wi-Fi); below them are Physical address (MAC), Link speed, Address, Gateway and DNS servers.
Confirm within 60 seconds after changing the IP
When you change the IP of the wired network while working through that very cable, you're disconnected as soon as the change is made, and the device has no way of knowing whether you can still reach it. So:
- The edit window says: "If you are using this cable to reach the device, the connection will drop after the change. Note the new address and open this page from it within 60 seconds to press “Confirm”, otherwise the change is reverted automatically."
- After applying, "Applied — waiting for confirmation" appears and tells you which address to open.
- Open "Network → Ethernet" from the new address. The top of the page shows "Change to adapter name awaits confirmation" with the seconds remaining; press "Confirm".
- On success, "Confirmed — the settings are kept" appears. Without confirmation within 60 seconds, the previous settings are restored automatically.
Changing only the DNS needs no confirmation.
Allow DFS channels
DFS is the "radar detection" that some 5 GHz channels require, and some on-site routers use these channels.
| Setting | Default | Description |
|---|---|---|
| Allow DFS channels | Off | "When on, the device can join a Wi-Fi network on a DFS channel, but the hotspot briefly drops if radar is detected." |
- Off (default): while the hotspot is on, the device avoids DFS channels when joining the on-site Wi-Fi. If the router's 5 GHz has only DFS channels, the device may join its 2.4 GHz instead, or the switch fails with "Reason: this network uses a DFS channel, which is not allowed alongside the hotspot."
- On: the device can join routers on DFS channels, but the hotspot may then be turned off ("The Wi-Fi uses a radar-detection (DFS) channel, so the hotspot is off").
- Pure "Station" mode (hotspot off) isn't affected by this setting.
Network status notices
These notices appear under the affected row on the "Network" page:
| Notice | Meaning |
|---|---|
| Hotspot channel follows the Wi-Fi network and cannot be chosen | Normal in Concurrent mode |
| Hotspot is limited to 2.4 GHz | The on-site Wi-Fi is on 2.4 GHz, so the hotspot moved to 2.4 GHz too. Devices that support only 5 GHz can't see the hotspot |
| The Wi-Fi uses a radar-detection (DFS) channel, so the hotspot is off | With "Allow DFS channels" on, the on-site Wi-Fi landed on a DFS channel |
| To keep the hotspot, the device joins on a channel without radar detection | With "Allow DFS channels" off, the device joined on another channel to keep the hotspot |
| The hotspot subnet overlapped the Wi-Fi network and was adjusted automatically | The on-site network happens to use the same subnet as the hotspot, so the hotspot switched to another subnet automatically. The hotspot's management address changes with it; check the new IP Address in "Hotspot" |
The network after a factory reset
After a factory reset:
| Item | Result |
|---|---|
| Hotspot name, password, security type and other settings | Back to this device's factory values |
| On-site Wi-Fi networks added by users | Deleted |
| On-site Wi-Fi networks marked "Factory" | Kept |
| Allow DFS channels | Back to off |
See Factory reset.
Signal and distance tips
- 5 GHz signals pass through walls less well; work within sight of the device.
- When the signal is below about -75 dBm, uploading images or updating software may be slow or interrupted; move closer to the device.
Related: Connecting to the device, Startup screen and screen language, CMS / standalone mode switching, Export / import settings, Device info and monitoring