Power control and storage
Navigation: Settings → Power → Power Control
The Power Control page offers two functions: "Reboot" and "Shut Down".
Factory reset isn't here
The factory reset entry is at the bottom of the "Settings → System → Software Update" page. See Factory reset.
Reboot
When to use it: the management interface behaves strangely, a feature is stuck, or you want to reload after changing settings.
- In the "Reboot Device" row, press Reboot.
- Confirm "Rebooting will temporarily disconnect all connections. Continue?".
- The device first clears the screen, then reboots. The confirm button shows a spinner until clearing finishes.
- On success, "The system will reboot shortly" appears.
- The management interface disconnects and "Lost connection to the device" appears at the top of the page. After about 1 minute, reconnect to the device (hotspot or on-site Wi-Fi) and refresh the page.
What the panel shows after the reboot:
| Startup screen setting | Panel after reboot |
|---|---|
| "Show QR Code startup screen on boot" on (default) | Shows the QR code startup screen |
| Off | Stays white until the next scheduled image change or until you display an image manually |
The original image doesn't come back automatically after a reboot
The page says: "Restart the system to try to recover from a software issue. It returns to the startup screen when done, and schedules continue as usual." After a reboot the panel shows the startup screen or white and does not automatically show the image from before the reboot. If you have a schedule, the image changes at the next scheduled time; if not, display an image manually.
Shut down
- In the "Shutdown Device" row, press the red Shut Down.
- Confirm "After shutdown, the device needs to be manually restarted. Continue?".
- The device first clears the screen, then shuts down. On success, "The system will shut down shortly" appears.
- Battery models notify the power board, which cuts the power after about 20 seconds.
You can't power it back on remotely
Shutting down cuts the power completely. Unlike sleep, it can't be woken by a schedule or a button. After shutdown, someone has to handle the power on site to start it again. If you only want to save power, use sleep instead.
Recommended way to shut down
Press Shut Down in the management interface first, and remove the power after the status LED goes off. On 27.6-inch and 32-inch models you can also shut down by holding the power switch on the device for 4 seconds.
Why the screen is cleared before shutdown and reboot
A cholesteric LCD keeps the last image indefinitely after power is removed. If power is cut without clearing the screen, the panel stays on the same image for a long time. So before shutdown, reboot and switching to CMS mode, the system clears the screen at the highest priority:
- Any refresh in progress is stopped, and clearing the screen goes first.
- If clearing fails, it retries automatically 2 times.
- If it still fails, the system still shuts down or reboots so the device doesn't get stuck unable to shut down. In that case the panel may still show the old image; check that the screen is normal after the next startup.
When a battery model is shut down by holding the power button, it also clears the screen before cutting power.
Long-term storage
Before leaving the device unused for a long time, moving it, or sending it for repair, follow these steps:
- On the "Image Display" page, press Clear screen, wait for "Screen cleared", and check that the panel has been cleared to a single background color (black or white).
- In "Power Control", press Shut Down and wait for the status LED to go off.
- Disconnect the external power as instructed for your model.
- Store it in a dry place out of direct sunlight.
Although the shutdown process clears the screen too, clearing it manually first and checking with your own eyes keeps the panel from being left with an old image if clearing fails.
Messages
| Message | Meaning |
|---|---|
| The system will reboot shortly | The reboot command was run |
| The system will shut down shortly | The shutdown command was run |
| Reboot requested. The screen will be cleared before restarting. | Same as above (shown in some cases) |
| Shutdown requested. The screen will be cleared before shutting down. | Same as above (shown in some cases) |
| System action failed. Please try again later. | The command failed |
Related: Sleep and wake-up, Battery, Factory reset