Time, time zone and clock sync
Navigation: Settings → System → Time Settings
Schedules, waking from sleep and system logs all run on the device's time. On first installation, after moving to another time zone, or after the device has been without power for a long time, make sure the time and time zone are correct before setting up schedules.
Page information
The top of the page shows:
| Item | Description |
|---|---|
| Time (large text) | The device's current time HH:mm and date |
| Time zone | For example Asia/Taipei (UTC+08:00) |
| Sync Status | "Synced (NTP)" or "Not Synced" |
The page updates automatically every 60 seconds; press Refresh in the top-right corner to update it right away ("Time updated" is shown). These automatic updates don't count as "someone using the device", so keeping this page open doesn't stop the device from going to sleep.
Three ways to set the time
| Method | Best for | Limitation |
|---|---|---|
| Sync Local Time | Most situations: sets the time from your phone or computer | Not available while NTP is on |
| Set time manually | When you need a specific time | Not available while NTP is on |
| Set time automatically (NTP) | When the device is connected to an on-site Wi-Fi network with internet access | Can't sync when the device has only its own hotspot |
Sync Local Time (recommended)
"Immediately sync the device's time to your browser's current local time"
- Make sure the time on your phone or computer is correct.
- Press Sync Local Time.
- On success, "Time synchronized successfully" is shown.
Set time manually
- Under "Set time manually", press Change.
- In the window, use "Select date" and "Select time" (hours:minutes:seconds). You must choose both; otherwise you are prompted "Please select date and time".
- Press Confirm. On success, "Time set successfully" is shown.
Manual time uses your browser's time zone
The date and time you choose are interpreted in your phone's or computer's time zone. If the two time zones differ (for example, your phone is on Taiwan time and the device is on UTC), make them match first, or use "Sync Local Time" instead.
Set time automatically (NTP)
"When on, the device automatically syncs its clock via an NTP server; manual time setting is disabled while syncing"
- When it's on, "Sync local time" and "Set time manually" are disabled (to avoid conflicting with automatic clock sync).
- On success, "NTP auto-sync enabled" / "NTP auto-sync disabled" is shown; on failure, "Failed to update NTP setting".
- When the device runs only its own hotspot ("Hotspot" mode), it has no outside network, so it can't reach a time server, and the sync status will always be "Not Synced". In that case, keep it off and use "Sync Local Time" instead.
- Only when the device is connected to an on-site Wi-Fi network with internet access in "Station" or "Concurrent" mode can it set the time automatically with NTP. See Network settings.
- If you see "The service failed to start — another time-sync service on this device (e.g. ntpd) may be using the same network port" after turning it on, another time service on the device is conflicting. Contact technical support.
NTP servers
On the "NTP servers" row you can enter your own time servers (for example a time server inside your company). When none is entered, the row shows "System default (…)", meaning the servers built into the device are used.
- On "NTP servers", press Set.
- Enter a host name or IP and press Enter. You can add several, up to 5.
- Press Save. "NTP servers saved" is shown.
Clear them all and save to go back to the system default.
Sync status
While NTP is on, the sync status at the top of the page also shows:
| Shown | Meaning |
|---|---|
| Last synced time (server) | When the clock was last synced successfully, and which server was used |
| Not synced since boot. Check the network and NTP servers | No sync has succeeded since the device started. Check that the device can reach the network and that the servers you entered are correct |
Device Timezone
"Sets the device's timezone, affecting displayed time and when schedules run"
- Under "Device Timezone", press Change.
- In "Search timezone...", type a city name (for example Taipei, Tokyo) and select the time zone.
- Press Save Timezone (the button is grayed out when nothing has changed).
- On success, "Scheduled jobs switched to new timezone" is shown.
If "Timezone saved, but scheduled jobs require a service restart to apply" is shown, restart the device from Power Control.
You can also sync the time zone in one step from the "Timezone mismatch" notice on the schedule page. See Schedules — Time zone.
After you change the time zone, existing schedules and light schedules keep the clock times they were set to and trigger according to the new time zone. You don't need to save them again.
Hardware clock (RTC)
The device has a hardware clock (RTC) that keeps running while the device is asleep or shut down:
- When waking from sleep, the system corrects its time from the hardware clock, so sleep doesn't make the clock fall behind.
- The system also corrects the system time from the hardware clock regularly.
- If the hardware clock can't be read, a red "Real-time clock (RTC) fault" warning appears at the top of the page, and the time may gradually drift. If any schedule is enabled, the device doesn't go to sleep (so that schedules aren't left unable to wake it). See Hardware warnings.
What a wrong time affects
| Feature | Effect |
|---|---|
| Schedules, light schedules | Trigger at the wrong actual time |
| Waking from sleep | Wakes up by the schedule time, so a wrong time means waking at the wrong time |
| System logs | Recorded times are wrong, making it hard to match events when troubleshooting |
When you move the time forward by more than 2 minutes, schedules in the skipped period are not run afterward; the device simply waits for the next scheduled time.
FAQ
Q: The sync status is always "Not Synced"? NTP can't sync when the device has no outside network, which is normal. As long as the time itself is correct, it doesn't affect use.
Q: The "Sync Local Time" button is grayed out? "Set time automatically (NTP)" is on. Turn off NTP first, then sync.
Q: The time drifts again after a while? The hardware clock may have a fault or its battery may be depleted. Check whether an RTC fault warning appears at the top of the page; if so, follow the warning or contact technical support.
Related: Schedules, Sleep and wake-up, Troubleshooting: schedules and time