Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the multi-panel bulletin board full feature guide as PDF

Installation and wiring ​

Navigation: Installation

The "Installation" page is for checking that every panel is connected, that the numbers match the nameplates on the back of the panels, and for dealing with replaced panels and moved ports. The page follows the steps ① Wiring, ② Identify, ③ System screens, ④ Export / import, and finally the panel firmware.

Applicable models

Only the multi-panel model with three 31.5" panels has the "Installation" page, see Bulletin board and single-panel settings.

Wait a moment after sending

After a wiring operation (register, swap, move) the screen shows "Sent. The panel service is restarting; takes effect in about 10 seconds". Wait about 10 seconds before looking at the result.

Wiring ​

"① Wiring" lists the state of every port, for example "3/3 panels connected".

SituationWhat is shownWhat to do
Normal"No. N" and the port nameNothing
One panel not connected"Missing (port name): check this panel's CH347, cable or TCON"Check that panel's cable and TCON
A whole group not connected"Whole group missing: check the USB hub or its upstream cable"Check the HUB and its upstream cable
Plugged into an unregistered port"An unregistered panel is plugged into (port name)"The panel is not refreshed; press "Register"

Register ​

Press "Register" to register the port as a new panel number. Use the number on the panel's nameplate and fill in the "Port name". A number already in use shows "No. N already exists". Once registered, the panel can be given content.

Moving settings ​

When a panel is replaced or plugged into another port, the old number is "Missing" and the new one appears. The Installation page then offers to move the settings of No. N to No. M. Press "Move":

  • The content, layout and rotation of the old number move to the new number together, and "Moved" is shown.
  • Tick "Stop using the port of No. N" to remove the old number from the wiring, so the healthy count no longer misses a panel. Do not tick it if the old port will be used again.

Identify ​

In "② Identify" press "Identify": every panel shows its number in large digits, to compare with the nameplate on the back.

Swap ​

If the number on screen does not match the nameplate (two panels were plugged in the wrong way round):

  1. Press "Swap" to open "Swap two panels".
  2. Choose the "First panel" and "Second panel", the two whose nameplates do not match (they must be different panels).
  3. After sending, the content follows the numbers; nothing needs to be set up again.

System screens ​

In "③ System screens" choose the "System screen panel": system screens such as the Wi-Fi QR code and network settings appear on this panel. Pick one that is low, close and easy to scan.

After the device restarts, the system screen panel first shows the startup screen (Wi-Fi QR code and admin page address) and switches back to its content after about 60 seconds. Panels that have no content yet keep showing the startup screen, with their own number (No. 1, No. 2…) on the left, so you can match them during installation.

Exporting and importing the wiring ​

"④ Export / import" carries the installation settings to the next site with the same model.

  • Export: exports the wiring, the system screen panel and each panel's layout.
  • Import: applies installation settings exported from a machine of the same model. Before importing it asks "Wiring, system screen panel and layouts will be replaced by the file's settings; content is not affected. Import now?". If the file is not an installation settings file, "This is not an installation settings file" is shown.

This file holds only installation settings, not content. To back up content and playlists use Export / import settings.

Panel firmware ​

"Update firmware" under "Panel firmware" updates the firmware of several panels, but one panel at a time:

  1. Upload one .bin firmware file.
  2. Under "Panels to update" tick the panels (each shows its current firmware version).
  3. Press "Start update". Each panel goes through "Waiting" and "Flashing firmware", then shows "Done: old version → new version" or "Failed: reason".

Do not unplug or power off during the update

Panels are flashed one at a time, about 20 seconds each. A panel does not advance while it is being flashed. Do not unplug or power off.

Related chapters: Bulletin board and single-panel settings, Media library, TCON firmware update

Green Ideas Technology