Skip to content
This page was translated from the Traditional Chinese original and has not yet been reviewed by a person. If anything is unclear, the Chinese version is authoritative.

Viewing: HTML | Download the E-Paper Content Management System manual as PDF

Schedule Settings ​

Where: sidebar → Content Management → Schedule Settings

A schedule decides what happens, on which devices, and when. At the set time, the schedule starts a playlist or sends a command to the devices (for example power off).

Only Platform Administrators and System Operators see this page.

Two places to create a schedule ​

Where you create itWhat you can setTrigger time
"Add Schedule Settings" on the "Schedule Settings" pageName, playlist, one or more devicesFixed at 1 minute after you save, repeating every day; you cannot choose it
"Device List" → "⋯" → "Task Management" → "New Schedule"Name, start a playlist or send a command, trigger time; applies to this one device onlyYou choose it yourself in Simple mode or Advanced mode

To choose the trigger time yourself, or to send a command on a timer, create the schedule from "Device List".

Schedule list ​

The list is ordered by priority. Each row shows the schedule's name, with "Edit" and a red delete icon on the right.

Changing the priority order ​

Above the list, the hint says "Drag to reorder priority — higher up runs first".

  1. Drag the handle icon on the left of a schedule to change its position.
  2. After dragging, "Priority order has changed. Click "Save" below to apply." appears.
  3. Click "Save" below to apply the change; click "Cancel" to restore the original order.

Priority order currently has no effect on execution

When two or more schedules trigger on the same device at the same time, every one of them runs; the system does not run only the top one by list order, and which schedule's content the device ends up showing is not fixed. When you save a schedule, the system also does not block settings that overlap in time with other schedules. This is a known issue; this page will be updated when it is fixed. Until then, avoid making schedules for the same device trigger at the same time.

Adding from the "Schedule Settings" page ​

  1. Click "Add Schedule Settings" at the top right.

  2. Fill in the fields:

    FieldDescription
    "Name"Required
    "Playlist"Required; choose the playlist to play
    "Device"Required; you can choose several
  3. Click "Save". Click "Cancel" to return to the list without saving.

About 1 minute after you save, the schedule triggers for the first time, and after that it triggers at the same time every day. The time is calculated in your computer's time zone.

Adding from "Device List" ​

In "Device List", find the device and click "⋯" → "Task Management" → "New Schedule"; the "New Schedule" window opens on the right. This schedule applies to this device only, and the last step shows "Locked to device: Device Name".

The window has two steps, "Content" and "Time". Click "Next" to go forward and "Back" to return, and finish with "Create schedule".

Step 1: Content ​

FieldDescription
"Name"Required
"Action""Start Playlist" or "Send Command"
"Playlist"Required when the action is "Start Playlist"
"Command"Required when the action is "Send Command"; see Sending a command

Quick create playlist ​

When there is no suitable playlist yet, click "+ Quick create playlist" below "Playlist" so you do not have to leave the window:

  1. In the "Quick create playlist" window, fill in "Name" and add "Sources" (the same as Sources).
  2. Click "Confirm"; the new playlist is selected in the "Playlist" field automatically.

A playlist created this way is always "Loop" and everything else is left empty. To adjust settings such as "Default Interval", edit it later on the "Playlists" page.

Sending a command ​

CommandResult
"Power Off"Powers the device off
"Takeover"See the note below
"Release Control (Switch to Standalone)"Returns the device to local control
"Reset Display"Clears what the device is showing, the same as "Clear Current Screen" in "Device List"

"Takeover" currently cannot be used to create a schedule

If you choose "Takeover" and click "Create schedule", an error appears and the schedule is not created. This is a known issue; this page will be updated when it is fixed. To take over a device, click "Takeover" by hand in "Device List".

A command has the same restrictions as sending it by hand from "Device List"; see Command restrictions. If a device cannot accept the command when the schedule triggers (for example it is under local control, or its previous command has not been answered), that device is skipped this time and not retried.

Step 2: Time ​

First choose "Simple" or "Advanced (cron)".

Simple mode ​

The "Weekly schedule grid" is a table: days "Sun" to "Sat" across, and every full hour from 00:00 to 23:00 down. Click a cell to select it and click again to deselect it. Each selected cell means one trigger at that hour on that day. Times are calculated in your computer's time zone.

The selected cells must form a complete rectangle: every day you select must have the same hours selected. For example, Monday to Friday at 08:00 and 18:00 (10 cells) works; selecting 08:00 only on Monday and 09:00 only on Tuesday does not.

MessageCause
"Select at least one weekly time slot, or switch to advanced mode."No cell is selected
"This selection can't be represented as a single rule. Select a full rectangle of days x hours, or switch to advanced mode."The selected cells do not form a complete rectangle

When you need different hours on different days, create several schedules, or use Advanced mode.

Advanced mode ​

Build the repeat rule with drop-down menus. After "Every" at the start, choose the period:

PeriodYou can also set
"year"Month, day of month, day of week, hour, minute
"month"Day of month, day of week, hour, minute
"week"Day of week, hour, minute
"day"Hour, minute
"hour"Minute
"minute"Nothing more to set; triggers every minute

An item you do not set means every one of them triggers. For example, with the period "day", hour 9 and minute 00, the schedule triggers every day at 09:00. The default is every day at 09:00.

Do not choose "reboot" in the period menu

The last option in the period menu is an English item, "reboot". If you choose it, the schedule triggers every minute. This is a known issue; this page will be updated when it is fixed.

"Timezone" defaults to your computer's time zone. You can choose another time zone, and the schedule then triggers at times in the chosen time zone.

What happens when a schedule triggers ​

ActionResult
Start a playlistThe playlist starts from the first source, and tasks on the device that have not finished become "Superseded". For how playback works, see How playback works
Send a commandThe command is sent to every device the schedule applies to
  • The actual trigger may be a few dozen seconds later than the set time. This is intentional, so that many devices do not act at exactly the same moment.
  • When a device is under local control, schedules do not send images to it.
  • If you do not want to wait for the schedule time, use "Trigger Schedule" in "Device List" to run it once right away; see The "⋯" menu.
  • The schedules that apply to a device are shown under "Schedule Settings" at the bottom of that device's "Edit Device" page.

Editing a schedule ​

Click "Edit" on the row of the schedule you want to change to open the "Edit Schedule Settings" page. You can change "Name", "Playlist" and "Device", then click "Save".

Saving an edit resets the trigger time

Whatever time was set before, after you save the trigger time becomes 1 minute after saving, repeating every day. A time set from "Device List" in Simple or Advanced mode is also replaced. This is the current design; this page will be updated when it changes. To keep the original trigger time, delete the schedule and create it again.

Deleting a schedule ​

  1. Click the red delete icon on the row of the schedule you want to delete.
  2. The confirmation window says "Once confirmed, this schedule will be permanently deleted and cannot be undone."; click "Confirm Delete".
  3. "Schedule deleted" appears.

After deletion, the playlist this schedule was playing also stops changing images, and the device stays on the screen it was showing.

Related pages: Playlists, Task List, Device List

Green Ideas Technology